We are a Florence commercial roof repair contractor fixing leaks, split seams, and worn metal on business, plant, and farm buildings. Every repair starts inside, where the water shows.
Most Florence commercial roof repair calls trace back to five zones on the roof, and each zone fails in its own way.
Wind lifts coping and edge metal at the corners first, and a peeled edge lets the next storm drive rain under the membrane. Sealant at coping joints cracks after a freeze-thaw winter.
Open laps on TPO, EPDM, and PVC sheets let water run sideways under the membrane before it finds a way down. Punctures from tools, hail, and boots cluster along service paths.
Clogged strainers, loose clamping rings, and cracked scupper corners sit right where water collects, so any gap there gets soaked every rain. Plugged downspouts push water back over the box.
Rooftop unit curbs, pipe boots, and pitch pans cover a small part of the roof and cause a large share of its leaks. Dried pitch pan fill and loose base flashing at curb corners are the usual culprits.
Insulation soaks up water and lets it go slowly, which is why a ceiling can drip days after a storm. Wet boards left under a patch spread the damage, so moisture checks come first.
Each repair follows four steps, from the first drip mark inside to the photos you keep on file.
Crews mark each stain and drip inside, then walk the roof above and uphill of it, checking seams, flashing, drains, and unit curbs.
Moisture readings and a press test around each suspect spot show whether water has reached the boards under the membrane or panels.
Seams get welded or taped, metal laps get resealed and refastened, and wet boards get cut out before a matching patch goes on.
Dated photos of every repaired spot on the roof go to you, so the next storm check has a baseline to compare against.
A targeted repair keeps the existing roof in service where the insulation is dry, and the work stays on the problem spots.
Repair fixes the specific spots where water gets in while the rest of the membrane or panels stay in place. Tenants keep working, stock stays put, and the roof system already over the building keeps doing its job.
Sealing the actual entry point keeps water out of the insulation and the steel deck under it, so the stain inside stops growing.
Each repair is logged with its spot on the roof and its photos, which shows over time whether one curb or drain keeps failing.
Spring and fall checks catch freeze-thaw cracks at sealant joints and leaf-packed drains before they become ceiling stains.
Move stock and electronics away from the drip, set out buckets, and photograph the stain. Then call and tell us where the water shows up.
(859) 205-4037Four repair services cover the flat, metal, and industrial roofs found on Florence business buildings.
Split seams, blisters, punctures, and ponding on TPO, EPDM, PVC, and built-up roofs, closed with welds, tape, and round-cornered patches.
Best for: offices, strip centers, and warehouses with low-slope roofs
Flat roof seam and drain repair
Backed-out screws, rusted end laps, crumbled ridge closures, and leaking gutters on exposed-fastener and standing seam buildings.
Best for: shops, pole buildings, and steel warehouses
Metal building screw and end lap repair
Leaks traced from the ceiling stain to the entry point, with hose testing when the source hides along deck flutes or purlins.
Best for: any building with a stain that keeps coming back
Tracing commercial roof leaks
Repairs planned around production, with hot work permits, unit lockouts, and walkway pads along busy service paths.
Best for: plants, distribution centers, and process buildings
Plant and warehouse roof repairA moisture survey draws the line between these three paths, so it comes before any recommendation.
Commercial Roof Repair
We take commercial roof repair work in Florence, three towns with their own pages, and seven more nearby. Outside them? Call us or send us a message.
Question about your own roof?
Call UsShort answers to what owners ask before a crew goes up.
Repair targets the spots where water gets in: open seams on TPO, EPDM, and PVC, punctures, loose flashing at parapets and curbs, clogged or cracked drains, backed-out screws, rusted end laps, and cracked pitch pans or pipe boots. The rest of the roof stays in place, and each job starts with a check for wet insulation under the damage.
Temporary patches buy time during a storm, and nearly every one needs a permanent repair once the weather allows. Roof cement smeared on TPO or PVC also blocks welding later, so the crew has to cut it out first. Tape or a compatible sealant makes the cleaner stopgap.
Edges, membrane surfaces, and rooftop equipment get the first look. Wind peels edge metal and coping at the corners, and hail bruises single-ply sheets and dents metal panels, skylights, and unit housings. Bruised membrane can look fine and crack weeks later, so suspect spots get pressed and the insulation checked. Dated photos help with an insurance claim.
Once new leaks keep appearing in different places and the insulation keeps getting wetter, each visit is fixing symptoms on a failing roof. A map of past repairs shows the pattern: clusters at one curb or drain point to a fixable detail, while leaks scattered across seams and flashing point to restoration or replacement.
Most repairs happen from the roof with the building open. Crews protect the floor under active leaks, and work over server rooms, sort lines, or sales floors gets scheduled with the owner. Hot work near flammable dust, or a unit shutoff at a curb, is planned ahead with the facility staff.
Stay off it. Wet membrane, wind, and lightning make a storm walk dangerous, so roof checks wait for clear weather. From inside, move stock away from the drip, mark stained ceiling tiles, and photograph each drip with the time. Those notes speed up the trace once a crew can go up.
Tell us where the water shows up and what the roof is made of, and we will set up a visit to trace it.
Want a call back about your roof?
Leave a name and number, or call (859) 205-4037 now.